How to make a homemade WiFi signal booster that really works and is also free? step by step guide

Currently the use of the Internet has become a necessity for all people, especially for big companies, in such a way that it is vital to have a good signal that covers all areas of work or home. That is why today there are WiFi signal boosters which will help you Internet coverage reaches those places where it did not before or its speed is improved.

Due to all these problems, users need to find equipment to help them solve these problems, however, network amplifiers They are usually somewhat expensive and not everyone has access to them. Due to all this, they have created home amps that will also help you improve the performance of your Internet coverage.

That is why here we bring you some tricks so that you can create your own signal booster in a free way and it really works. It is important to mention that you do not need to be an expert to be able to do this, you simply have to follow the steps that we will explain below and in a matter of minutes you will be able to have your own equipment to improve wireless internet signal in your living or workplace.

Steps and tricks to make a homemade Wi-Fi repeater antenna

The coverage of your wireless Internet It will depend a lot on the type of house, where it is located and the type of router you are using, any of these options can influence coverage. These problems with the passage of time have been able to be solved thanks to the devices for improve Wi-Fi signal.

Today there are different tricks and ways to create a signal amplifier yourself with which you will be able to solve this type of problem and the best of everything will be totally free, since you will not need expensive materials to be able to do it.

In such a way that if you want to create your own home computer you just have to follow the steps that we will explain below:

Home WiFi with a can of beer

This trick is one of the most common to do to try to improve the Internet signal in your home or office, with this method you will be able to create a repeat that will allow you to concentrate all WiFi coverage in a directional waythis will allow you to direct the entire signal to where the devices you want to connect to the wireless network are located.

Keep in mind that the direction will be an imaginary line that you will draw from where is your router located to where the other equipment you want to connect are.

In order to carry out this method, you need to have the following materials at hand:

• An empty beer or soda can.
• Industrial scissors.
• Insulating tape
• A cutter.

How can you see all these materials can be found at home and they usually do not have a high cost. For equipment manufacturing you have to follow these steps:

• The first thing you have to do is take the beer can and with the cutter you are going to cut the entire bottom part, the goal is to be able to remove the entire bottom of the can. In the event that it is easier for you with the scissors, you can also use them for this step.

• This same cut must be made in the top of the canbut this time you have to leave a piece of the can that remains attached to the rest of the container.

• Now very carefully and with the help of scissors you are going to cut the outline of the container from the bottom, in this way it will look like a cylindrical parabolic

• We will place the top of the can as antenna basea, as indicated in the photo.

• Once this is done the WiFi repeater antenna will already be completed, it only remains to do the installation on the router.
• For this it will be necessary to use the tape to be able to fix it, preferably it is recommended to use the can hole where does the drink come from insert the antenna and then you adjust it with the help of the tape.

It is important that before fixing the homemade antenna you have chosen the direction in which you want send signal. Once this is doneyour work will be finished.

Home WiFi with Aluminum Foil

This is another of the tricks that you will be able to use to improve the WiFi signal in your home, this method is not new, quite the contrary, it has been used for a long time and thanks to its good results it is still valid.

Currently there are many users who for some reason have failures in their coverage which makes them have a bad signal or low speed. Due to this it has become popular the aluminum foil method, where its main function is route the wireless signal.

Surround the router with a beer can or aluminum foil will help you reduce the interference and thus create different barriers so that you can increase the security and speed of the connection.

In order to carry out this method, it is important that you have the following materials at hand:

• A card.
• Kitchen aluminum foil.
• Stick or liquid glue.
• Scissors to cut aluminum foil.

Once you have all the instruments ready, all you have to do is start with the manufacture of your signal antenna wireless internet. To do this you will follow these steps:

• The first thing you have to do is cut a card the size of an A4 sheet.

• Once you have the rectangular figure cut you are going to cover with aluminum foilfor this you are going to use the glue and you must wait a few seconds for it to dry.

• It is important that you use another paper figure that you are going to glue to the rectangular one, you can also do this with cartulina and you cover it with aluminum foil. You will use it to introduce the antenna of the router and as support for the aluminum foil.
• Once all this is done, all that remains is to enter the antenna of the modem by the figure and your work will be done.

Create a homemade WiFi antenna with a can of Pringles

This method is usually more complicated than the previous two. However, it is considered one of The best home wireless internet signal boosters. In this case, the main objective is to be able to replace the main antenna of the home router with a new homemade antenna, which will be made with a can of pringles.

In this case, you are going to create a directional homemade antenna. Therefore, you must be sure what direction you want to give it, since it will point to a specific place.

If you want to perform this method, it is important that you have the following materials on hand:

• A rod 140mm long and 3mm wide.
• 10 x 15mm diameter washers.
• 10 x 3mm threaded nuts.
• 5 washers of 30 mm outside diameter and 6 mm inside diameter.
• A pot of pringles potatoes of 170 grams.
• An adapter or USB key.
• A male-female USB extension cable of approximately 5 meters.
• A support may be plastic material.
• A cardboard lid.

once you have all the materials ready and at hand, it only remains to start with the elaboration of the homemade antenna for the wireless network, for this it is important that you perform the following steps:

• The first thing you’re going to do is take the rod together with the washerswhich you are going to introduce in the rod to form the figure that appears in pictures.

• This will serve to facilitate the reception of the frequency waves.
• At the time of introduce the washers it is important to be very careful with the distance of each of them, this will help the wave performs the parabola as best as possible. At the ends of the rod it will have two caps, one will be a plastic cap and the other will be a cardboard cap, both are used to support the equipment.

• The next thing is to take the Pringles pot and open a hole on one of its sides, this has to be just the size of the WiFi USB key so that it can be inserted and adjusted.

• Once done you have to insert the rod with the washers through the pot of potatoes, To do this, you will first enter the cardboard lid, which will be the base of the container, while the plastic lid will be the main lid of the container.
• Once all this is done We introduce the USB flash drive to the container.
• Finally we create a support where the homemade Pringles antenna will gothis can be made of plastic, metal or the material that the user has at hand and can fulfill this function.

• Once all this is done, the manufacture of the antenna will be finishedit only remains to connect it to the modem and start using it to see its results.

A WiFi repeater using an old router

Today many users are still unaware that an old modem can be used as an access point plus increase the signal of the wireless network. In this way you will be able to improve the quality of the coverage for free by simply using the equipment that you thought was no longer useful.

In order to create a new access point with an old router and be able to increase the WiFi signal, you need to have the following instruments:

• new router.
• old router.
• Ethernet cable.
• Computer.

Once you have these materials at hand, you simply have to follow the steps that we will explain below:

• To start you have to choose the place where you want locate the old router, note that this has to go connected to the current and it has to be located between the main router and the area where you want boost Wi-Fi signal.
• you have to use the ethernet network cable so you can unite both teams. (they don’t connect yet)
• Plug into the outlet the old modem near the computer and you have to reset it. Note that all of these teams have a bbutton on the back to be able to perform this function.
• Now you have to join the old device with the ethernet cable with the computerthis will be only momentary, while the setting.
• Once they are connected you have to enter one of the browsers, in the search bar you are going to write the following address: 192.168.1.1 so you can enter the address of the router.
• In the event that an error message appears, try this address: 192.168.1.2
• A window will appear on the screen asking you to enter username and password, you should look for it in the equipment manual, in one of the stickers on it or in its box. If it doesn’t show up you can try Admin/admin or admin/1234.
• After having accessed the router configuration you have to create a new WiFi network, Write down the name and password you choose.
• The next thing will be to access the configuration of the Red lan. Here you have to check the IP addressif the main team has 192.168.1.1 you can assign the old team the address 192.168.1.2.
• Now check that the option is activated Enable DHCP Server Relay or similar. And finally you will save the changes.
• Disconnect the cable and with a mobile or a laptop you will check that it is detected the new Wi-Fi network that you have created
• reconnect the cable to the computer and again enter the settings from the computer by repeating the steps above.
• When you have entered again you will look for the section of the DHCP server.
• There you have to make sure that it appears disconnected, if it is not like that, disconnect it or disable the “DHCP Server” Y “Save changes”
• Once all this is done you will disconnect the old equipment from the computer and place it in the place that will be its position.
• The next thing will be to turn off both equipment, both the new and the old and They connect via Ethernet cable.
• Finally you’re going to turn on only new equipment and wait for it to set, after turn on the old computer.
• Both computers will start working and the old router will serve as an access point receiving internet by cable and thus transmitting its wireless signal.

Is it more effective to increase the Wi-Fi signal to recycle an old router or to make a homemade antenna?

Today there are many tricks to be able to increase the WiFi signal in your home, from using potato cans, aluminum foil, beer cans, or an old router, among many others. Considering that some of them are homemade tricks with which you will not have the need to spend money and you will be able to obtain good results.

Taking into account that the easiest solution will be to throw away the broken or faulty router and replace it with a new, much more powerful one. However, many of the users have doubt or concern to know which method is more effective in order to improve wifi internet signal and therefore obtain better results.

It should be noted that of the four methods that have been explained the most effective for this is using an old router but, keep in mind that this method requires spending money, therefore, it may not be in the options of many users.

But, through this method the results will be faster, since you have two routers that will be transmitting a WiFi signal at greater range and power. So if what you want is boost WiFi signal and improve performance of the same the best option will be to use an old router as an access point with the help of a new equipment.