Currently the use of the Internet has become a necessity for all people, especially for large companies, in such a way that it is vital to have a good signal that covers all areas Work or home. That is why today there are WiFi signal amplifiers which will help you to Internet coverage reach those places where before it did not or improve your speed.
Due to all these problems, users are in need of having to look for equipment that will help them solve these problems, however, network amplifiers are usually somewhat expensive and not all People have access to them. Because of all this, homemade amplifiers have been created that will also help you improve the performance of your Internet coverage.
That is why here we bring you some tricks so that you can create your own signal amplifier in a free way and it really works. It is important to mention that you do not need to be an expert to be able to do this, you simply have to follow the steps that we will explain below and in a matter of minutes you can have your own equipment to improve the wireless Internet signal in your living or workplace.
Index:
Steps and tricks to make a homemade Wi-Fi repeater antenna
The coverage of your wireless Internet will depend a lot on the type of home, where it is located and the type of router you are using, any of these options can influence the coverage . These problems over time have been solved thanks to the devices to improve the WiFi signal.
Today there are different tricks and ways to create a signal amplifier yourself with which you will be able to solve this type of problem and best of all it will be totally free, since You also won’t need expensive materials to do it.
So if you want to create your own home team you just have to follow the steps that we will explain below:
Homemade WiFi with a can of beer
This trick is one of the most common to do to try to improve the Internet signal in your home or office, with this method you will be able to create a repeat that will allow you to Concentrate all Wi-Fi coverage in a directional way , this will allow you to direct all the signal to where the devices you want to connect to the wireless network are located.
Keep in mind that the address will be an imaginary line that you will draw from where your router is located to where the other devices you want to connect are located.
In order to perform this method it is necessary that you have the following materials on hand:
- An empty beer or soda can.
- Industrial scissors.
- Duct tape
- A cutter.
As you can see all these materials can be obtained at home and usually do not have a high cost. To manufacture the equipment you have to follow these steps:
- The first thing you have to do is take the beer can and with the cutter you will cut the entire bottom , the goal is to be able to remove the entire bottom of the can. In case you find it easier with the scissors you can also use them for this step.
- This same cut should be made in the top of the can , but this time you have to leave a piece of the can that remains attached to the rest of the container.
- Now with great care and with the help of scissors you will cut the outline of the container from the bottom, this way you will be left as a cylindrical parabolic .
- We will place the top of the can as base of the anten a, as indicated in the photo.
- Once this is done the WiFi repeater antenna will already be completed, it only remains to perform the installation on the router.
- To this will be necessary to use the tape to fix it, preferably it is recommended to use the can hole where the drink comes out to insert the antenna and then adjust it with help of the tape.
It is important that before setting the home antenna you have chosen the direction in which you want to send the signal. Once this is done , your work will be finished.
Homemade WiFi with aluminum foil
This is another of the tricks that you will be able to use to improve the WiFi signal in your home, This method is not new, but quite the opposite, it has been used for a long time and thanks to its good results are still valid.
Currently there are many users who for some reason have flaws in their coverage which makes them have a bad signal or with low speed. Because of this, the aluminum foil method has become popular , where its main function is to route the wireless signal.
Surrounding the router with a can of beer or foil will help you reduce interference and thus create different barriers so you can increase connection security and speed .
In order to perform this method it is important that you have the following materials on hand:
- A cardboard.
- Aluminum foil.
- Glue stick or liquid.
- Scissors to cut the foil.
Once you have all the instruments ready, you only have to start manufacturing your signal antenna of wireless Internet . To do this you will follow these steps:
- The first thing you have to do is cut a cardboard the size of an A4 sheet.
- Once you have the rectangular figure cut you will line it with the foil , for this you will use the glue and you must wait a few seconds for it to dry. >
- It is important that you use another paper figure that you are going to stick to the rectangular one, you can also do it with c artulin and the foil with aluminum foil . You will use it to introduce the router antenna and as a support for the foil.
- Once all this is done, just enter the modem antenna by the figure and your work will be over.
Create a homemade WiFi antenna with a can of Pringles
This method is usually more complicated than the previous two. However, it is considered as one of the best homemade wireless internet signal amplifiers. In this case the main objective is to be able to replace the main antenna of the router of the house with a new homemade antenna , which will be manufactured with a can of pringles.
In this case, you are going to create a directional home antenna. Therefore you must be sure which address you want to give it, as it will point to a specific place.
If you want to perform this method it is important that you have the following materials at hand:
- A rod 140 mm long and 3mm wide.
- 10 washers 15 mm in diameter.
- 10 nuts 3 mm thread.
- 5 washers of 30 mm outside diameter and 6mm inside diameter.
- A pot of pringles potatoes of 170 grams.
- A USB adapter or key.
- A male-female USB extension cable of approximately 5 meters.
- A support can be plastic material.
- A cardboard cover.
Once you have all the materials ready and at hand you only have to start with the elaboration of the homemade antenna for the wireless network, for this it is important that you perform the following steps:
- The first thing you are going to do is take the rod along with the washers , which you will introduce into the rod to form the figure that appears in images .
- This will facilitate the reception of frequency waves.
- When introducing the washers it is important to be very careful with the distance of each one of them, this will help the wave make the parable the best possible . On the tips of the rod it will have two covers, one will be a plastic lid and the other will be a cardboard lid, both are used so that the equipment is supported.
- The next thing will be to take the Pringles pot and open a hole on one of its sides, it has to be just the size of the USB WiFi key > so that it can be inserted and fit.
- Once done you have to introduce the rod with the washers through the pot of potatoes, for this you will first enter the cardboard lid which will be the base of the container, while the plastic lid will be the main lid of it.
- Once all this is done we introduce the USB pen drive to the container.
- Finally we create a support where the home antenna of Pringles will go , this can be made of plastic, metal or the material that the user has at hand and can fulfill this function.
- Once all this is done, the fabrication of the antenna will be finished , it only remains to connect it to the modems and start using it to see its results.
A WiFi repeater using an old router
Many users still do not know that an old modem can be used as an access point and also increase the wireless network signal. In this way You can improve the quality of coverage for free by simply using the equipment you thought was no longer useful.
To be able to create a new access point with an old router and to be able to increase the WiFi signal it is necessary that you have the following instruments:
- New router.
- Old router.
- Ethernet cable.
- Computer.
Once you have these materials at hand, you simply have to follow the steps that we will explain below:
- To start you have to choose the place where you want to locate the old router, keep in mind that it has to go connected to the current and it has to be located between the main router and the area where you want to increase the WiFi signal.
- You have to use the Ethernet network cable so you can connect both computers . (They don’t connect yet)
- Connect the old modems to the power socket near the computer and you have to reset it. Keep in mind that all these devices have a oton on the back to perform this function.
- Now you have to connect the old device with the Ethernet cable with the computer , this will be only momentary, while the configuration.
- lasts Once connected they have to enter one of the browsers, in the search bar you are going to write the following address: 192.168.1.1 so you can enter the router address.
- In case you see an error message, try this address: 192.168.1.2
- On the screen you will see a window where you will be asked to enter username and password , you should look for it in the manual of the equipment, in one of its stickers or in its box. If it does not appear, you can try Admin / admin or admin / 1234.
- After accessing the router configuration you have to create a new WiFi network, enter the name and password you choose.
- The following will be to access the settings of the LAN network. Here you go than checking the IP address , if the main team has 192.168.1.1 you can assign the old team the address 192.168.1.2.
- Now check that the Enable DHCP Server Relay or similar option is enabled. And finally you will save the changes.
- Disconnect the cable and with a mobile or a laptop you will verify that the new WiFi network is detected that you created.
- Reconnect the cable to the computer and again enter the configuration of the device repeating the previous steps.
- When you have entered again you go to look for the DHCP server section.
- There you have to make sure that it appears disconnected, if it is not, disconnect it or deactivate the “DHCP server” and “Save the changes”
- Once all this is done you will disconnect the old computer from the computer and place it in the place that will be your put on.
- The next thing will be to turn off both computers, both the new and the old and connect via the Ethernet cable.
- Finally you will turn on only the new team and expect it to configure , then you turn on the old device .
- Both computers will start working and the old router will fulfill the function of an access point receiving internet over the cable and thus transmitting its wireless signal.
Is it more effective to increase the Wi-Fi signal recycle a old router or make a homemade antenna?
Today there are many tricks to increase the WiFi signal in your home, from using potatoes, foil, beer can, or an old router, among many others. Given that some of them are homemade tricks with which you will not have the need to spend money and you will be able to get good results.
Bearing in mind that the easiest solution will be to discard the broken or broken router and replace it with a much more powerful new one. However, many users have the doubt or concern of knowing which method is more effective in order to improve the WiFi Internet signal and therefore obtain better results.
It should be noted that of the four methods that have been explained the most effective for this is to use an old router but, keep in mind that this method requires A money expense therefore, may not be in many users’ options.
But, through this method the results will be faster, since you have two routers that will be transmitting a WiFi signal with greater range and power . So if you want to increase the WiFi signal and improve the performance of it, the best option will be to use an old router as an access point with the help of a new computer.