The mBlock programming platform of the company Makeblock, is one of the newest programming tools for beginners. If you are looking to get inspired with new ideas, then check here what are the best MakeBlock and Arduino projects you can do. 2022 list.
The mBlock’s friendly interface let you wirelessly program your robots in Scratch blocks to Arduino source code. Through this language there are many inventions that you can replicate.
All the information of the sensors who will receive the plaque, will be sent via USB cable via firmware, previously downloaded to the program.
List of the best projects with MakeBlock and Arduino that you can make yourself from scratch
The advantage of mBlock is that, as you develop the instructions for the program, you can see the “real code” which uses the Arduino board. Either for educational purposes or because you simply want to expand your knowledge.
Whatever the reason, here is a list of the best MakeBlock and Arduino projects that you can do yourself from scratch:
Ingenious Traffic Lights with Multiple LEDs
Control two traffic lights conditioned to a car on hold or not. For it, you need to simulate a crossing with traffic lights where the presence of cars is detected to Activate or deactivate the traffic lights.
In this simulation you will use buttons and the following materials:
- 6 x 220 Ω resistors
- 2 x Red LEDs
- 2 x Yellow LEDs
- 2 x Green LEDs
- 2 x Pushbuttons
- 2 x 10 k resistor (pull down)
Theremin with LDR
Although it is an electronic musical instrument, the Theremin, you don’t need physical contact to make it ring. For this proposal, you need to represent the frequency change of the Theremin using an LDR light sensor. When you bring your hand closer to the sensor, the sound will increase of frequency. By pushing her away, will decrease.
The components that you must have to build this project are:
- 1 x Piezoelectric
- 1 x LDR photoresist
Soil moisture sensor
This experiment is very simple to perform, you just have to feed to sensor with ground (GND) Y Vcc. Then the output pin reading will be performed with an analog pin of the Arduino. In this case, you must connect the sensor to the Arduino board on pin A0, by means of the pins Dupont type Funduino.
Here are the materials to use:
- Arduino Edushield Board
- Glass of water
- Humidity sensor
LCD screens
This handy project is to show different characters that teach messages or visuals with Arduino through a small screen. They are a very simple alternative to use. In addition, they give a very professional and commercial touch.
To replicate this work, these are the required components:
- 16 x 4 LCD screen
- Arduino UNO board
- 2 hoses
Simple button
For this Proyect you need to program a switch and light an LED with Arduino on a certain moment. The Pull-Down and Pull-Up resistors They are the main elements that will allow the correct functioning of this work.
The materials to be used are the following:
- 1 Arduino UNO board
- 1 Breadboard
- 4 hoses
- 2 Resistors
- 1 led diode
Locate colors
The mission of this program is basically to discover the colors where the mBlock character moves to activate the different Led diodes from the Arduino board.
To represent this project yourself, you will need:
- 1 Arduino UNO board
- 1 Breadboard
- 4 hoses
- 3 Led diode
- 3 Resistance
Servomotor
The main instruction for this program Its the move the servomotor from its original position to a final position at 10 ° angles repeatedly.
All you need are these items:
- 1 Arduino UNO board
- 3 Hoses
- 1 Servomotor
Compass with Servo
In this exercise the task consists of move a servo using the keyboard arrows and activating the two LEDs at the end of the race.
The materials to execute the project are:
- 1 Arduino UNO board
- 1 Breadboard
- 3 Hoses
- 2 Led diode
- 2 Resistance
- 1 Servomotor
Temperature sensor
With this of this practice it is required level the intensity of 3 LED bulbs using a potentiometer, to observe its values from its position of minimum resistance to maximum resistance.
To meet the project requirements you will need:
- 1 Arduino UNO
- 1 Breadboard
- 7 Hoses
- 3 LEDs (red, orange and blue)
- 3 100Ω resistor (brown-black-brown)
- 1 LM35 temperature sensor
Evening RGB LED
The Evening LED is a project in which it is necessary to use an LDR light sensor. Its function is to change the colors of an LED belonging to the RGB range. In other words, it should light up in different colors as it darkens through a range of colors.
For this, you will need the following materials:
- 1 Arduino UNO
- 1 Breadboard
- 7 Hoses
- 1 common anode RGB LED
- 1 LDR sensor
- 1 100Ω resistor (brown-black-brown)
- 2 220Ω resistor (red-red-brown)
- 1 10KΩ resistor (brown-black-orange)
Get to know the best Arduino kits and boards to work with MakeBlock and get the most out of it
Everything beginner programmer you need a simple resource that allows them to start code development. The arduino packages they are a good alternative for those looking to make their own configurations.
For this reason, we leave you a list of the best Arduino Kits and boards to work with MakeBlock and get the most out of it:
Arduino Starter Kit for Beginners K030007
Consists in a base material to review classic concepts electronics and programming. It is recommended for any type of user with minimal or no programming knowledge. Contains 100 components in total, including one Arduino UNO Rev3 board, a 7-inch LCD screen, a set of sensors, cables, LEDs of different colors, motors and resistors.
ELEGOO ES-EL-KIT-008
A fairly complete resource, with 200 components, among which are: an Arduino Mega 2560 R3 board and an expansion card. Too includes more than 60 types of sensors to develop projects. Such is the case with the LCD 1602 module, which has the ability to teach up to two rows of 16 characters. In addition, it offers a manual in Spanish, which will guide you step by step in the world of programming in Arduino.
Smraza S48F
It is a particular option to carry out the greatest amount of programming projects with Arduino. The Smraza S48F board is an Arduino Mega 2560 R3 compatible tool. It has different motor modules, a 1602 four and seven segment LCD display, a joystick and a great diversity of sensors.
Freenove Ultimate Starter Kit
It is a considerably cheaper tool, ideal for those who just want to try the product. This article includes an Arduino UNO R3 compatible board, and contains over 200 components to program. Additionally, it provides a guide in English and in PDF format to show you basic notions of electronics and explains the development of 51 projects so that you can replicate it yourself step by step.
KeeYees Basic Starter Kit by Arduino for Beginners
In the last place is another low cost alternative. This is the KeeYees Basic Starter Kit, which brings an ATmega328P development board, 100% Arduino compatible. The package includes items such as: a micro servor motor, LED lights, LED lights, resistors to work more easily. It also offers you 256 parts of up to 33 different component types and modules. Their lessons are explained in a simple way so that start programming quickly.