How to fix headphones that have stopped ringing? step by step guide

Index:

UPDATED ✅ Do you need to repair the headphones that are not heard and you do not know how? ⭐ ENTER HERE ⭐ and discover how ✅ EASY and FAST ✅

Headphones are an important piece when wanting listen to music, or some voice note in private either in our smartphone or computer. However, these accessories have a useful life or in many cases begin to deteriorate due to use and time.

So if you’re starting to have a problem with your hearing aids, either because only one side sounds or simply cannot be heard, there are some ways that can be carried out to try to repair them before going to the store for new ones.

But before discovering methods to repair them It is important to note what they are. the main reasons that these accessories no longer workwhich we explain below.

What are the possible reasons why my headphones no longer work?

The useful life of any accessory will depend largely on the care they receive, on many occasions using them in a bad way can cause damage, either removing them from the Smartphone the wrong way or simply how they are stored, this can cause them to begin to fail in some way, thus prolonging their deterioration.

Because of this, here we are going to teach you what are the possible reasons why the headphones can stop working shortly after purchase or with the time of its use.

Physical damage: On many occasions at the moment of wanting disconnect the hearing aids from the smartphone finished pulling the cable and not the connectorkeep in mind that this can exert unnecessary tension that will end up being damaged over time.
Keep your hearing aids connected: In general, when hearing aids are discontinued they are usually left connected on mobilethis can cause the cable to become entangled with an object and create tension in the cable that can cause damage.
Hang up the headphones: Mostly people usually hang up the headphones either in your handbag or just somewhere desk to save them. However, gravity can affect them, since they will be stressing unnecessarily and this could affect the connection.
Put them on the ground: Leaving your headphones on the floor can be a double-edged sword, as you could end up accidentally damage it. Therefore, it is always recommended to leave them in a safe place, either on a table or simply put them away.
Wrap the cord when not in use: It can be said that this is one of the most common mistakes with cables, keep in mind that if the cable is twisted or kinked can affect the connection of the cable, this will cause it to not be heard well or simply stop ringing.
Have contact with water: Any electronic device you can be affected by this. In general, hearing aids can easily become damaged if they come into contact with water. If this happens it is important that you dry it immediately and place it outdoors.

Steps and methods to fix iPhone, Samsung or any brand headphones at home

Keep in mind that if the damage to your headphones is not very serious, they can be fixed simply using a few methods. But, this will basically depend on how serious the damage is.

As usual, Most of these failures are due to The cable has connection problems, the headphone jack has problems, or you just can’t hear it through one of the headphones.

In this way, here we present some ways to repair them and thus avoid buying new ones:

repair connector

One of the most common problems that we can find in headphones is with the connectorit is usually damaged when we remove it in a bad way or simply we pull the cable to release it from the mobile phone.

In this case, it is best to replace said connectoreither using a other hearing aid connector that you have it in good condition or simply buying one in some electronic accessories store.

For this, it is important to perform the following steps:

The first thing to do is find a metal connector with a stereo connection. It is important that this connector is the same size as the one we are going to replace.

repair connector

The next thing will be to renew the outer cover of hearing aid wires at least ½ inch or 1.25 cm of the bare wire. There you will find a cable red, one green and two copper wires.

repair connector

Now you have to separate the red and green wires of the two copper. The two copper cables are going to be joined by means of a braid to make one.
In the new connector you will unscrew the metal part from the plastic cover. Now roll up very carefully the three wires via the base of the new connector. They will be exposed at the end of the plastic cover.
The next thing is to put the metal part of the connector on the screw, You are going to paste it with a tape or weld it so that it is much safer. you solder the wires on itbased on the metal part of the new connector, while copper wires are soldered on the outside of the terminal. The green wire to the middle terminal and the red wire to the third terminal. Once this is done, wait a few minutes while the solder cools down.

repair connector

Lastly, it must remove the metal part of the connector from the screw. It is important to insulate the hearing aid cables from the connector, in the same way to make sure that no part of the wiring has been left exposed, it must be covered by the insulating tape. Thus, your new metallic connector will be ready to be used again with your mobile phone.

repair connector

fix the speaker

In many cases the damage of hearing aids is due to the horn or loudspeaker, in the event that this is the problem of the accessory then we can carry out its repair with a few steps. However, it will be necessary to have a speaker with the same characteristics as the original so that the repair can be carried out successfully.

In order to do this, you will need to perform the following steps:

To start you will need disassemble the headphonesNote that this process varies by hearing aid model.

fix the speaker

For this it is necessary loosen the headset screws, Usually a screwdriver is needed. size crosshead 0.
On many occasions they usually have two or three screws. Once you are sure that you have released everything, you can carefully remove the filling.
Now insert some flat tool into the crack of the base of the hearing aid dome to help their separation.
Hearing aids can usually be separated, but you may need to a new rubber stamp then for their union. The problem is almost always in the headphone cable.

fix the speaker

On many occasions when the problem is the cables, this can be seen with the naked eye. either some loose or broken cable which needs to rejoin the controller. This will require finding metal pins and re-soldering the wire in the correct position so that it begins to make contact again. It is important that none of the cables touch each other.

fix the speaker

Controller can also be replaced if it is the case, but keep in mind that this can be a bit expensive. In the case of wanting to replace the controller completely, it is recommended to seek a specialized technician in the area, since this is usually a little more delicate and if it is not done correctly the hearing aid can be completely damaged.

However, if you want to do it yourself, you can follow these steps:

the first thing will be cut the rubber stamp around the center layerThis can be done with the help of a sharp, fine knife.
then it remove the tapered driver.
Now place the new driver with the same characteristics as the previous one and in the same slot. It is important that the controller do not touch the thin diaphragm.
Once placed it is recommended add some glue around the edge to make it more secure.
Lastly, it is important to make sure that none of the wires make contact with each other.

fix the wire

One of the most common damages to headphones is from the wireThis is because on many occasions is rolled up and stored the wrong way thus causing it to come apart. This may cause the sound that is emitted from it be interrupted repeatedly or even stop ringing at times.

In this way, here we explain what steps to take to correct this type of problem:

Before attempting to carry out a headphone cable repair it is recommended test the wire in order to find out where the break is. For this it is necessary to use the headphones and carefully we bend them from the speaker and slide it along the wire. When the sound stops, the problem has been found.

fix the wire

With a piece of tape we can mark the place where cable break is found.
Now with the help of a wire stripper or a blade the outer layer of the cable must be cut, it is recommended remove 1.25 cm or half an inch of the outer armor.

fix the wire

Next, it must extend the cut in any direction so that the broken cable can be seen.
In this case you can find two wires glued together, each will contain a isolated cable that is the signal and a bare cable that is the ground. In the case of apple headphones have two insulated wires and a single ground wire.
Once the place of the problem has been identified, the following will be cut the wire in two. If the cable is scratched, it is recommended to cut both sides to eliminate the problem. In this case, the same amount of cable should be removed from the side. left and right.

fix the wire

If only one of the wires breaks, it can lead to skip the soldering step, no cutting or splicing required, which will make the process much faster.

fix the wire

The cable’s rubber cover should slide back while repair is done and once it is finished, it is covered with it again to protect cables.
The next thing will be to splice the cables, that is, to join the cables. In this case it is important Join wires with the same color insulation. There are two options a flexible cable splice and an in-line splice.
In the case of flexible cable splicesthe two exposed areas of the cable to be joined must be lifted, placed parallel to each other and twisted into braids to join them.

fix the wire

In the case of online splices, the wires must be overlapped end to end and then turned in opposite directions, a more difficult process but easier to hide the repair.
now it takes use a soldering iron to melt a small amount of solder onto the wires, This must be repeated in each of the connections so that they are well sealed and allowed to cool.

fix the wire

Once cooled, it should be kept the red and white ends separated of the ground wire, wrapping the two pairs of joints with the insulating tape to avoid possible contact between them.
When there is covered with duct tape correctly one can use heat gun to tighten it and prevent it from loosening over time.

fix the wire

When the audio only comes from one side

It is possible that at the time of use and connect your headphones the sound is only emitted by one of them. This usually means that there is a connection problem in said earphone, in this case the damage may be near the connector or along the cable.

To do this, the following will have to be done: