Have a good internet connection it is practically essential today. In this sense, there are different ways to access the network. On the one hand, it can be done through a Ethernet network or also with a WiFi connection.
Many users choose WiFi because it is more intuitive to configure, but this does not mean that it is the best option. If what you are looking for is speed and make the most of the speed navigation, the most recommended is connect via ethernet.
Therefore, in this post we will explain How to configure the Ethernet connection of your Windows 10 to have a faster Internet?. In addition, you will learn about the main differences between the two connections and some useful tips to navigate faster.
Ethernet vs WiFi What is the best way to connect to the Internet in Windows 10?
As we explained previously, that the WiFi connection be more popular, does not mean that it is the most efficient. It is even proven that use an ethernet network cable it is much faster and more efficient.
One of the main reasons that decrease WiFi performance are:
- Interferences, obstacles and distance: These three elements cause the performance of the WiFi connection to decrease considerably. For example, if devices with electromagnetic waves such as mobile phones are near the router, the connection may be impaired. Also, the connection drops if the router is too far from the computer, or if there are obstacles such as walls.
- Channels and saturation: The channel used by the WiFi connection can be shared with the neighbor connections, so this saturation causes the performance to be reduced.
But nevertheless, this problem is not found when using an ethernet cable. In those cases, the chances of interruption are less, so they have a performance much more stable and consistent compared to wireless connections. If you have a computer whose operating system is Windows 10will always be a better option to work with ethernet cable connection. This way you squeeze the maximum speed of data transfer from one device to another.
Learn step by step how to configure your Ethernet network to browse faster in Windows 10
If you have never configured an Ethernet network to be able to navigate at full speed, you don’t have to worry. Is a simpler procedure than it seems.
With this in mind, we share the step-by-step to follow on Windows 10 computers:
Identify which is the network card
The network card It is an essential part of being able to connect a computer to the Internet, even through it it is possible to enter the network with a certain speed. With the emergence of fiber optics, connection speeds have increased considerably, reaching up to 1 Gb.
But really, to be able to enjoy it, you need to have your computer’s network card configured correctly. The first step in this regard is to make sure we have a 10/100/1000, that is, let it be compatible with speeds up to 1 Gb / s. This particular guy has the name of Gigabit Ethernet.
For their part, there are Fast ethernet characterized by reaching a maximum of 100 mb, which means that it limits the user in terms of browsing speed. Today, modern computers have a built-in Gigabit Ethernet network card, which makes them perfect to withstand the fastest speeds. So identify what your type is And, if you have Gigabit Ethernet, it is time to know the configuration you have.
Access the network card settings
- Go to the taskbar icon, which is located below on the right.
- There is the internet icon. Click on it and go to Network and Internet Settings.
- Click on the option Ethernet. This will take you to the card settings. Once there, tap on Change adapter options.
- Shows the different network cards that the equipment has. Usually there will be the card Ethernet and the wireless.
- Double click on the option Ethernet card and the information about it will be displayed.
These dates tell us the speed. It can be displayed as 100.0 Mbps or 1 Gbps. If the last speed is displayed, i.e. 1 Gbps it means that the card is properly configured. If otherwise 100.0 Mbps displayed, it is necessary to carry out a series of settings.
Configure at 1 Gbps
- Inside the same window that you were already in (where speed was shown) you have to press Properties.
- Then make sure the option of Client for Microsoft networks. Next, tap on Set up.
- Go to Advanced Options and search Speed & Duplex.
- It is time to change the value. Probably if that step was reached, it is because it is configured as 100 Mbps Full Duplex. However, you have to change it to 1.0 Gbps Full Duplex Y To accept.
In this way, you will have your network card configured in Windows 10 for what support high speeds and you can enjoy a much faster connection.
Tips to make your Internet connection go faster in Windows 10
While it is true that browsing speed It depends on the plan you have contracted with your operator, you may be losing speed at some point due to different factors. In the case of computers with Windows 10, there are some helpful tips you can follow to improve browsing speed.
We share the main 5:
Reboot and relocate the router
If at any time you notice that your browsing speed is reduced from time to time, before trying any internal settings, we recommend you first reboot the router and move it location. The reason is that there may be interference from some other electronic device.
Select a channel that is not clipping
Sometimes, the connection may be affected if the channels are saturated. This usually occurs mainly in communities with many neighbors and where there are many nearby WiFi. The cause of this lies in that wireless routers operate in channels and one of them may be more saturated than others.
To solve it, you can try changing channels and checking if the connection improves. On the Internet you will find tools that allow you to check which channels are the most free. You can try, for example, with WiFi Analyzer.
Check if someone else uses the WiFi
If someone managed to connect to your WiFi network, they may be hogging a good chunk of bandwidth. To know if this is happening you just have to disconnect all devices from the WiFi network and see if the lights on the router blink indicating that activity is present.
Likewise, you can take advantage of third-party applications such as Wireless Network Watcher and thus scan the connection to know which devices are connected. Remember that if anyone else is online, you may harm when enjoying speedy navigation.
Clear DNS cache
The DNS servers They are in charge of resolve domain names, which means that when you put an address Url in the navigation bar, a server DNS interprets the information and relates it to a IP adress. Consequently, it is possible to view web pages normally.
Within all this process, the operating system makes a dump DNS resolution information and stores it locally in a cache, with the aim of reducing the loading times of previously visited websites. The problem with this is that the information may be incorrect and this causes the loading time to be longer than normal. This gives the impression that the Internet connection has dropped. If you are experiencing slowness, you can do a DNS cache flush manually.
To achieve this, you have to go to the main screen of Windows 10 and, on the taskbar, use the search box next to the Start button to open Command Prompt right click. Then you have to select in Execute as an administrator. When the command console opens, type the command ipconfig/flushdns. Click on Enter so that the DNS cache. When you’re done, some of the connection issues may be fixed.
Remove the bandwidth limit in Windows 10
Go to the main screen of the operating system and use the taskbar finder (located next to the start button) to write the command gpedit.msc. Then press Enter or select in Edit group policy, which should be the first search result.
When the window opens, go to the left sidebar and select the section of Equipment setup. From there, locate the option Administrative templates for. Then click Network / Qos packet scheduler / Limit reservable bandwidth.
In case it appears as “Not configured”, which is the default setting, it means that no type of Internet connection speed restriction should be applied. But if you want to be 100% sure, select the option and a new window will automatically open. Inside it, click on the option Enabled and below, in Options, change the value of Bandwidth limit (%) from 80 to zero. Finally, click on Apply and ready.