There are many problems or failures that can occur on a computer when we want to establish a connection to the Internet. One of the most popular on Windows computers is the «Ethernet does not have a valid IP configuration ».
Many of the users are not familiar with this type of problems, so it can be frustrating to solve it, especially if the person does not have much knowledge regarding the subject. However, it is easier to solve than it seems.
If you were presented with the error of “Ethernet does not have a valid IP configuration” In Windows 10, don’t worry. We will help you by Detailed step-by-step guide on how to fix it and enjoy your internet connection.
What are the causes of the “Ethernet does not have a valid IP configuration” error?
It is very frustrating for many people who work with computers, not knowing how to solve a problem when it occurs and much more if it affects the Internet connection. In this sense, it is very common to encounter the error message of “Ethernet does not have a valid IP configuration”.
This notice means your private IP is invalid. Remember that the Private IP It is the one that is assigned to your team. So the main cause for this error is because of a incorrect value at any of the following points:
- DNS
- The subnet mask from your team
- The gateway used
In case you don’t know how to fix it, you don’t have to worry. We will help you through a step-by-step guide how to make this error disappear in Windows 10 and you can proceed to enjoy your Internet service easily.
Steps to fix the error “Ethernet does not have a valid IP configuration” in Windows 10
There are several methods that will allow you to get rid of the annoying “Ethernet does not have a valid IP configuration” error. The main ones are changing DNS, restarting the Winsock catalog, updating the computer controls or restoring Windows to its old version.
Taking this into account, We will talk about the steps to follow in each case:
Changing DNS
- Right-click on the icon located on the taskbar next to the clock, whose name is “Net”.
- Get in “Open Network and Sharing Center”.
- Select the network you are in and press the button “Properties”.
- Go to “Internet Protocol version 4 (TCP / IPv4)” and select again in “Properties”.
- In the box that you can see, select “Use the following DNS server addresses” and write the following numbers: 8.8.8.8 and 8.8.4.4.
- Finally, click on “Validate configuration on exit” and accept. Then wait for the Network diagnostics and ready.
Restart the Winsock catalog
To restart Winsock catalog You must first access the Windows command console as an administrator. For this, you must click start (It is located in the lower left corner of the screen, with the Windows icon). Then you have to write “Cmd”.
Then it shows you the option to “Command Prompt”. Click on this option with the right mouse button and select “Execute as an administrator”. Once you are clear on this, apply the following steps:
- Disconnect the network cable to avoid any type of connection between the modem and your computer with the damaged ethernet configuration.
- Enter the Windows command console and type “Netsh winsock reset” and expect Windows to do the task.
- You will be asked to restart your computer to save your changes. Finally, reconnect the network cable and the Internet should work normally.
Updating computer drivers
First of all, you have to know the way to update computer drivers in Windows 10 It is done in the same way that other areas such as network adapters, printers, monitors, etc. are updated, that is, by installing by Windows Update.
To proceed with an efficient update, follow these steps:
In case Windows can’t find a new driver, tWe recommend looking for one directly on the manufacturer’s website. device and follow its prompts.
Restore Windows to a previous version
On some occasions, the error of “Ethernet does not have a valid IP configuration” after an update. In these cases, it is a good idea restore to a previous version. The correct form is indicated below:
- On the Windows Start menu, type “Control Panel”.
- Then click “Recovery”.
- After that, you must select in “Open”, “System Restore” and then in “Following”.
- Finally, choose the Restoration Point to which you prefer to return and select “Finalize”.
I am still not connected to the Internet. What can I do in this case?
Despite having tried all the methods explained above, you may still have problems connecting to the Internet. We know it is very frustrating, so the best alternative in these cases would already be communicate directly with the service provider.
The fault may come directly from the provider, so asking them for help is a good option. They are familiar with the matter and will be able to help you make this error go away.